Showing 25–36 of 87 results
-
Outdoor A-Boards
( reviews)£42.00-
- Outdoor A-Board Pack (2 × 590mm × 1000mm)
-
- Outdoor A-Board Pack (3 × 390mm × 1000mm)
-
- Outdoor A-Board Pack (4 × 290mm × 1000mm)
-
- Outdoor A-Board Pack (4 × 590mm × 420mm)
-
- Outdoor A-Board Pack (6 × 390mm × 420mm)
-
- Outdoor A-Board Pack (8 × 290mm × 420mm)
-
-
Piccadilly Roller Banner
( reviews)£339.00These templates will help you create your design at the correct size, shape and proportion for the Piccadilly Roller Banner, and are setup at 20% scale of full size.
The bottom 30mm area (150mm at full size) must only be used for background colours/images or left blank. This section will be hidden and rolled into the unit mechanism. Your 2150mm tall design should bleed at least a third of the way into this area to allow for any height variance of the unit and prevent any white edge showing.
Please allow a 6mm (30mm at full size) quiet area for any important content from the very top of the artwork (see guide). This will ensure the top metal rail doesn’t interfere with your design.
For our InDesign, Illustrator and EPS templates, instructions are located off-page on a separate, locked layer. However, our PDF templates show instructions within the page.
When supplying your print-ready artwork, please follow our artwork requirements.
-
Pole Banner
( reviews)£25.00Pole Pockets
A pocket is added to the edges you require to allow a pole to pass through and support/tension the banner.
The diameter of the pocket can be specified by you, however, if you let us know the diameter of the object to go into the pole pocket we can calculate the size of the pocket for you.
For help on setting up your artwork for these finishes, please refer to our artwork setup guide.
Notice
Please be aware that banners are only temporary signage and we cannot be held responsible for any fitting or installation issues. As with all temporary signage they should be taken down in winds exceeding 30mph.
Artwork
To help ensure your artwork is processed quickly and without any problems, please refer to our artwork requirements.
-
Pop-up Banners
( reviews)£25.00The bottom 30mm area (150mm at full size) must only be used for background colours/images or left blank. This section will be hidden and rolled into the unit mechanism. Your 2150mm tall design should bleed at least a third of the way into this area to allow for any height variance of the unit and prevent any white edge showing.
Please allow a 6mm (30mm at full size) quiet area for any important content from the very top of the artwork (see guide). This will ensure the top metal rail doesn’t interfere with your design.
For our InDesign, Illustrator and EPS templates, instructions are located off-page on a separate, locked layer. However, our PDF templates show instructions within the page.
When supplying your print-ready artwork, please follow our artwork requirements.
Below is an unbranded product spec sheet for the Raptor Roller Banner that you can print, show on-screen or send to your customers. Spec sheets are not branded as Venture Banners in any way.
-
Pop-Up Carry Case Graphic
( reviews)£35.00Shape
- The red line is the bleed line. Artwork must extend to this line. The area in between this line and the front/side area lines must only be used as a quiet area.
- The purple line is the bleed line. This is the perimeter of the cut graphic area.
- The blue line is the finished line. This is the perimeter of the visible graphic area, after the graphic has been fitted to the unit.
- The green line is the front area line. Any design elements you wish to be clearly visible from the front (without following the curve of the graphic) should be kept within this area. Full size: 400mm × 727mm.
- The amber line is the side area lines. Any design elements you wish to be seen from the sides should be kept within these areas. Often used for sponsor logos, web addresses and other secondary content. Full size: 210mm × 727mm.
Layers
Please note, these templates contain a locked layer that is set to be non-printing. Any artwork elements that are put on this layer will not be included in exported PDFs, and will not be printed. Please check your exported artwork before sending it to us.
- Guides (Non-Printing) (locked). Must not contain any of your design elements. May be deleted, if desired.
- Design. Must be used to create and supply your design.
-
-
-
-
-
-
-
